MacBook Pro Rubber Feet 13" 15" 17" RETINA A1398 A1425 A1502 US Seller Lot

Description

Suitable for Apple macbook pro Unibody 13" / 15" Retina (2012, 2013, 2014)
Package includes 10 Piece Bottom Case Screws - 1 Pentalobe Screwdriver - 4 retina feet
Compatible model: MacBook Pro Retina A1425 A1502 A1398 all models
Macbook Pro RETINA Display Bottom Case Rubber Feet Replacement Set A1425 A1502 A1398 13" 15"
This kind of rubber feet are fit for macbook PRO Retina mac 13 mac 15 A1425 A1502 A1398 ONLY ,not for AIR ONES( A1370 A1369 A1465 A1466 ) PRO ONES(A1278 A1286 A1297)
Gloves are suggested for this procedure. Preliminary Step Before you begin, check the foot location requiring replacement and verify that the case plug, and the case foot in the kit, match the pictures below.
Place the computer upside down on a clean, lint-free cloth or other nonabrasive surface. Remove the bottom case.   Using the Pentalobe 00 screwdriver, remove the bottom case by removing 10 screws.
Important:
Screws at sides and front must be removed and installed at an angle.   Gently pull the bottom case from the side the display hinges are on and lift upwards at an angle.   Make sure the foot area on the bottom case is clean and free of debris. If any portion of the foot adhesive remains, peel it up with a pair of tweezers.   Clean both sides of the bottom case around the foot area. Allow the alcohol to evaporate.   Peel the outer foot from its packaging and affix it firmly to the bottom case. Use the glue to adhere the outer foot to the bottom case. Avoid touching the adhesive backing. Use a paperclip or safety pin to open the glue nozzle. A paperclip or safety pin can also unplug the glue nozzle after storage. Apply a very small drop of glue on the bottom of the foot on the bottom case. Do not spread the glue.  Seat the plug onto the glued area.   Do not use your finger to press the foot plug down. Use the wooden end of a cotton swab to press the foot plug into place. Lightly press and hold the foot in place for 30 seconds.   Clean any excess glue with a cotton dry swab.
Important:
Do not wipe the glue; use the cotton dry swab to absorb any excess glue. Excess puddled glue may take hours to dry and may cause the bottom case to adhere to the logic board or interior cabling.
Reassembly Note:
Install screws in order shown. If sequence is not followed, bottom case might wobble when placed on level surface.
Place the computer upside down on a clean, lint-free cloth or other nonabrasive surface. Remove the bottom case.   Using the Pentalobe 00 screwdriver, remove the bottom case by removing 10 screws. Important: Screws at sides and front must be removed and installed at an angle.
Place the computer upside down on a clean, lint-free cloth or other nonabrasive surface. Remove the bottom case.
Using the Pentalobe 00 screwdriver, remove the bottom case by removing 10 screws. Important: Screws at sides and front must be removed and installed at an angle.
Gently pull the bottom case from the side the display hinges are on and lift upwards at an angle.
Clean area with rubbing alcohol and allow to properly dry. Peel the outer foot from its packaging and affix it firmly to the bottom case. Use the glue to adhere the outer foot to the bottom case.
Clean any excess glue with a cotton dry swab. Important: Use the cotton dry swab to absorb any excess glue. Allow 15 minutes to properly dry before putting cover back on.
Reassembly Note: Install screws in order shown. If sequence is not followed, bottom case might wobble when placed on level surface.